product

The Ellipse Model ASF annular flanged, steam flow device is a multi-ported, self-averaging differential pressure flow element. Its innovative elliptical shape provides the lowest permanent pressure loss in the industry. The Ellipse flow meter is...

The Model PFA FM approved Fire Pump System features the Preso Ellipse. The Ellipse is a primary flow sensor designed to produce a differential pressure that is proportional to the flow. Its patented elliptical shape provides the lowest pressure loss...

The SoMat eDAQ-lite Non-Isolated Thermocouple Layer (ELNTB) measures temperatures on 16-channels of non-isolated thermocouple signal conditioning. Thermocouples come in several styles of dissimilar metals, or calibrations; and the ELNTB is...

Switch and splitter of incremental encoder...

...

The SoMat eDAQ Non-Isolated Thermocouple Layer (ENTB) measures temperatures on 32-channels of non-isolated thermocouple signal conditioning. Thermocouples come in several styles of dissimilar metals, or calibrations; and the ELNTB is compatible with...

EOLIS 0030A2 & EOLIS 0030A2F have been specially designed to be used as an interface for isolation and signal...

A two-channel independently isolated signal convertor of process signal...

EP150 is an easy-to-handle, hot-curing adhesive that is used in the process of strain gauge installation. In addition to being applied by a brush (included in the screw cap), EP150 can also be sprayed on. It is suitable for high ambient temperatures...

EP310N epoxy resin adhesive consists of two components and cures under heat and pressure. It is suitable for strain gauge installation for experimental tests usage, with extended temperature requirements and for transducer...

EPB is a small pressure probe sensor, small profile, stainless steel, flush mount transducer designed for general media. EPB is offered in pressure ranges from 0-5 to 5000 psi (0-0.35 to 350 bar), vented, sealed, and absolute pressure. EPB's overall...

The EPIH is a subminiature pressure sensor, specifically designed for Dynamic and High Frequency measurements with resonant frequency up to 1.7 MHz. Available with many various housings, EPIH is one of the smallest pressure sensors in the world. The...

The EPL is a surface mount pressure sensor with a stainless steel diaphragm. Available in ranges from 5 to 5000 psi (0.35 to 350 bar), EPL is easy to install on flat surfaces using elastomer or epoxy. Various compensated temperature ranges are...

Ultra Miniature Pressure Transducer, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

Miniature Pressure Transducer, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

Ultra Miniature Pressure Transducer with platinum RTD to sense media temperature, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

Blind plug M20 with...

Cable gland...

Cox Exact Dual Rotor Turbine Flow Meters are the pinnacle of turbine meter technology that delivers results not attainable with single rotor designs. The Exact meter’s hydraulically coupled helical dual rotor design provides exceptional...

Manufactured from common products like 316 SS or Monel® to more exotic alloys like tantalum, the RCV Exotic Alloy valves are available in 1/4", 1/2", 3/4" and 1" models, with interchangeable trim sets and threaded bonnet for quick disassembly. The...

Main processor layer for eDAQXR-lite...

The extended fin globe control valve is designed for modulating flow control in industrial or research applications at 1200° F or less and at pressures less than 5000 psi. The added bonnet length and fins serve to reduce the heat at the packing...

The EZ-100 Easy Mount Bracket Assembly takes all the hassle out of mounting traditional Speed Switches and Speed Sensors. The EZ-100 allows a Speed Switch or Speed Sensor to be mounted to a rotating shaft without the need of any additional brackets...

The EZ-SCP Easy Mount Bracket Assembly takes all the hassle out of mounting SCP-Series Speed Switches, and is ideal in new and retrofit applications. The EZ-SCP allows an SCP-Series Switch to be mounted to the end of a shaft without the need for any...

Electro-Sensor’s FB420 is an integral part of the Electro-Sentry™ Hazard Monitoring System but is also available as a stand alone shaft speed sensor. The FB420 provides a 4-20mA signal directly proportional to the rotational speed of a monitored...

The Badger Meter® FC-5000 Flow Computer is a microprocessor-driven device designed for flow monitoring. The FC-5000 is designed to be compatible with the complete line of Badger Meter industrial flow meters, creating a solution to totalize and...

The FC22 Series low cost compression load cells create new markets previously unrealizable due to cost and performance constraints. This series provides a new level of performance at very low cost. Measurement Specialties' proprietary Microfused™...

The FC23 Series low cost compression force sensors create new markets previously unrealizable due to cost and performance constraints. This series raises the bar in price and performance. Measurement Specialties’ proprietary Microfused™...

Cox FC30 flow computers service both liquid and gas applications. The FC30 features batching, 40-point flow meter linearization tables, and temperature viscosity correction using Strouhal/Roshko advanced linearization methods and multiple flow and...

The "F" in FDT Series stands for 'Flexible Leads'. These are rectangle elements of piezo film with silver ink screen printed electrodes. Rather than making the lead attachment near the sensor, the piezo polymer tail extends from the active sensor...

The Blancett FloClean sanitary turbine flow meter provides the high accuracy and rigorous design of the standard Blancett turbine in a sanitary-style tri-clamp mounting configuration. Developed for use in a variety of food, beverage and...

Measurement-Specialties’ washer load cell, model FMT, is designed to measure clamping and screwing forces. It is available in standard ranges from 0-4 klbf to 0-64 klbf.The sensor design reduces the hysteresis and sensitivity variations associated...

Measurement-Specialties’ load pins, model FN1010, are designed to fit in the place of the regular mounting unit. The implantation is facilitated by the possibility of modifying a certain number of dimensions. The FN1010 is suitable for numerous...

The FN2114 load cell has been developed for pedal load testing. Its size allows the sensor to be easily installed on the pedals of any vehicle or a fatigue/endurance test bench. Since the forces to be investigated on the brake, clutch or...

The FN2317 is designed with the express purpose of allowing quick and easy installation when measuring forces applied to the handle of the hand brake in automobiles. Through careful placement of metallic strain gauges inside the sensors, accurate...

The FN2420 is a high accuracy compression load cell often used in applications involving calibration presses. It is available in standard ranges from 0-4000 to 0-1000000 lbf and comes with many options, including a concave loading fixture and an...

The FN2570 load cell has been developed for pedal force testing. It attaches easily on all types of pedals and test rigs for endurance and fatigue tests, especially where size is an important factor. Strain is measured with high precision...

The FN2640 is specially designed for overseeing manufacturing processes. It measures with high consistency the regularity of compression load generated when fitting pieces. With its compact design and robust construction, the sensor easily...

The FN3030 measures tension and compression in standard ranges from 0 - 50N to 0 - 100 kN. The FN3030 is well suited for customization in industrial applications and protection levels can be upgraded for use in hostile environments. Additionally,...

The FN3060 S-beam load cell is highly suited for use in test benches and fatigue tests. Due to the mechanical design, the FN3060 is especially durable. It measures tension and compression in standard ranges from 0-50 to 0-500lbf. For high-level...

The FN3148 high precision load cell features accuracy of 0.05% F.S. It is available in standard ranges from 0-10 N to 0-2000 N . Integrated mechanical stops protect against accidental overloads in tension and compression. For high-level output a...

The FN3280 S-beam load cell is designed to measure low loads and comes in standard ranges of 0-0.2 lbf to 0-1 lbf. Integrated mechanical stops protect against accidental overloads up to 100 times F.S. The FN3280 provides a combination of economy and...

Measurement Specialties has applied our decade of experience serving the automotive crash test industry to design the ultimate crash test seat belt restraint sensor. Created for the automobile industry, the FN 4055 measures with excellent accuracy...

The FN4070 load cell measures the effort generated on the anchor point of seat-belts during crash-tests. It has been specifically designed with a replaceable tongue, so that the load cell can be re-used by simply changing the tongue. It also has a...

The FN6163-2 transducer is part of a whole measurement system, which allows verifying the correct pre-straining of the shafts and differentials in a gearbox. Made to the design of the original short secondary shaft, it accurately measures the axial...

The FN7080 is installed in place of the original gear knob on the gear stick of a vehicle and will measure the force required to change gear. Force is measured either in two or three directions. An adapter coupled with an interface collar allows a...

The FN7110 features high accuracy measurement channels in two ranges in the same load cell. The standard ratio between the ranges is 1 to 10, and standard load range combinations go from 0-2 and 0-20 lb through 0-200 and 0-2000 lb. The FN7110's...

The FN7178-2 is designed specifically to be mounted in series with a front wheel shock absorber on a vehicle. It measures the force in three directions to study ride characteristics under a wide range of driving conditions. Mono-directional versions...

The FN7180-3 is designed specifically to measure friction between two elements. Used mainly for automotive application, the sensor controls the efficiency of windshield soaps, elastomeric surfaces, oils and fluids under several conditions. The...

The multiaxial FN7325 measures force from 0-5 kN to 0-250 kN along three axes as well as the corresponding torque from 0-200 N.m to 0-7000 N.m. The FN7325 is simple to use and install and in many diverse applications circumvents the necessity of...

The multi-axial FN7384 is designed for force measurement for tool calibration. Designed for an automotive application, the complete sensor replaces with corresponding dimensions and tolerances, the piece the machine will produce. On strategic places...

The Model FN9620 is a S-Beam load cell with ranges from 500N to 10kN, designed to operate in hostile environments from -40 to 90°C with IP68 ingress protection. It provides high stiffness for high cycle use, low off-axis load sensitivity and high...

The FP110 is designed to measure static and dynamic pressure with the output characteristics substantially kept up to about 20% of the resonant frequency. The all stainless steel construction and flush diaphragm allow the sensor to be used under a...

The FP1124-3 HT Series of pressure transducers is designed specifically to measure pressure on the brake circuit, including ABS brake systems. With its rugged design and excellent thermal characteristics, the FP1124-3 is built to withstand high...

Adapters and patch...

The FS02 - BraggMETER tunable optical filter features a proprietary cavity design without guiding optics resulting in a compact, robust and vibration-resistant...

The FS19 load cell, with ranges from 500G to 3000G, uses proven Microfused sensor technology derived from demanding aerospace and automotive applications which employs micro-machined piezoresistive strain gages fused with high temperature glass to a...

The FS20 Series low cost compression force sensor creates new markets previously unrealizable due to cost and performance constraints. This series raises the bar in price and performance. Measurement Specialties’ proprietary Microfused™...

FS22 – Industrial BraggMETER DI - Dynamic (up to 1000...

FS22 – Industrial BraggMETER DI - Static (1...

The FS42 - Portable BraggMETER is an interrogator with embedded...

The FS62 - Athermal Strain Sensor is a Fiber Bragg Grating (FBG) based sensor with an innovative proprietary design that ensures athermal operation of the strain gauge by cancelling the intrinsic fiber optic thermal...

The FS62 - Strain Sensors are Fiber Bragg Grating (FBG) based sensors, designed to be bonded to surfaces and materials, spot welded to structures and components, attached or directly cast into concrete wet...

Heat-resistant | Completely non-metallic | Highly dielectric | Extended temperature...

FS63 Optical Temperature Sensors are suited for temperature measurements in large structures, such as Structural Health Monitoring(SHM) in civil structures and thermal mapping in electrical...

FS64 Optical Tilt Sensor is designed to measure small angle variations towards the...

FS65 Optical Accelerometer is designed to be used in a large range of monitoring applications, where low frequency and small amplitude vibrations are...

The FX1901 series establishes a breakthrough price/performance value for compression load cells. The FX1901 is a 1% load cell with full scale ranges of 10, 25, 50 or 100 lbf compression. This new, low-cost technology will enable force sensing in a...

G Series - Optimum strain gauge for the manufacture of transducers, for smaller...

The G-Series consist of a single axis conductive tilt sensor on a modern technology in environmentally protected and robust aluminum housing. The fast microcontroller works with a linearization and temperature compensation routines. This fully...

The Torque/RPM adapter enables the connection of HBM’s T12, T40B or similar torque transducers to GEN DAQ mainframes. The use of differential signals improves the immunity to external disturbance especially when using long cables in electrically...

The isolated Digital Event Adapter provides...

The Blancett QuikSert® In-line turbine flow meter provides the high accuracy and rigorous design of the standard Blancett turbine, but in a wafer-style mounting configuration. With a unique "between-the-flange" design, the need for mating flanges...

Cox Precision Gas Flow Meters are designed for precise and repeatable flow measurement of all compressible fluids, with the added benefit of minimal pressure loss. To accommodate the requirements of most gaseous flow applications, Cox Precision Gas...

GC-485 DigiSense™ Gage Head is available in five bipolar measurement ranges, with standard strokes from ± .050 inches to ± 1.0 inch. The single ended 8.5 to 30.0 volt dc. input and two-wire, addressable RS-485 output, make the GC-485 ideally...

GCA Series gage head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are...

The GCA-AE Series heavy-duty gage heads enable high performance in environments containing moisture, dirt, and fluid contaminants. These Gage heads are air-extend, spring-retract LVDTs (Linear Variable Differential Transformers) with precision...

GCD Series gage head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are...

The GCD-AE Series heavy-duty DC operated gage heads enable high performance in environments containing moisture, dirt, and fluid contaminants. These Gage heads are air-extend, spring-retract LVDTs (Linear Variable Differential Transformers) with...

The GCD-SE Series is available in five uni-polar measurement ranges, with standard strokes from 0 to 0.1 inch to 0 to 2.0 inches. Operating on a single ended 8.5 to 28.0 volt dc. input, and minimal current draw, the GCD-SE is ideally suited to...

The GCT Series Gage Head Transmitter is available in four different ranges from 0 to .250-inch, to 0 to 2.0-inches. This rugged two wire loop powered gage head is designed for harsh environments with its hermetically sealed stainless steel, housing...

The Preso Gemini differential pressure flow meter has a cone-shaped element that shapes the flow profile ahead of the differential pressure (DP) measurement port without impacting the flow against a sharp surface, creating an extremely stable signal...

GEN16t is a robust rack mount...

Rack mountable, 17 slots, with data streaming up to 100...

Perfect for portable use, with low channel counts or applications that require a distributed...

A powerful and fast portable transient data...

A powerful high speed DAQ designed for installation in control...

The GEN4tB is a universal transient recorder & data acquisition mainframe with 4 slots for input boards and high data throughput. Perfect for high speed acquisition with moderate channel count in the field, in the lab, and in the test...

Genesis HighSpeed mainframes are the indispensable basis for our versatile and extremely powerful data acquisition systems and provide all the features expected from a transient...

Rack mountable, 7 slots, with a data transfer rate of 400...

Genesis HighSpeed is the modular platform for fast measurements of electrical and mechanical parameters. A transient recorder, data recorder and data acquisition system – all in...

Solve your redundancy or dual device interfacing issues with the GK...

The Preso portable gage Model GM is a portable read-out meter designed to measure differential...

The Preso GMD Gage features a leak-proof round face plate with a 270° dial, balance valve and connections for instrument tubing. Each gage is furnished with a universal mounting attachment for flange or wall mounting as well as vertical or...

The power analyzer card offers three power channels, each one consisting of one voltage input and one current (or voltage) input. It is specially designed for efficiency measurements in inverter-driven electric drive systems and all tests in...

16-channel universal input with sample rate of 500...

The power analyzer card offers three power channels, each one consisting of one voltage input and one current (or voltage) input. It is specially designed for efficiency measurements in inverter-driven electric drive systems and all tests in...

32-channel accel input...

32-channel accel input...