Accelerometers

Designed for measurement of very high level, continuous vibration and mechanical shock up to 150 kms-2 and 1000 kms-2 peak,...

Designed for general purpose monitoring transducer and may be used in areas where there is...

Designed for measurements in harsh industrial...

Designed for vibration measurements in harsh industrial...

Designed for measurement of very high-level, continuous vibration, mechanical shock and...

Designed for measurement of very high-level, continuous vibration, mechanical shock and...

Designed with a high sensitivity and excellent signal-to-noise ratio for measurements on large structures at very low frequencies and measuring low-level seismic...

Designed for in-flight active vibration control on rotor and fixed wing aircraft and industrial...

Designed for low-level measurement, low noise and high...

Designed to operate in harsh environments with a robust 4-pin Glenair® 800-series connector for industrial...

Designed for low-level vibration...

Type 8347-C is a piezoelectric, shear design, charge...

Jewell Instruments DKA Series Accelerometers are an excellent choice for cost to performance trade off. The DKA is based on silicon micro-machined MEMS Capacitive Accelerometer technology and designed for low power and high...

Jewell Instruments DMA Series Accelerometers are an excellent choice for cost to performance trade off. The DMA is based on silicon micro-machined MEMS Capacitive Accelerometer technology and designed for low power and high stability. RS232 / RS485...

The DXA-100/200 single or dual digital accelerometer takes Jewell’s highly accurate analog closed loop sensor technology to the next level. Ranges from ±0.25g up to ±2g...

Meets CENELEC/AREMA Standards.  The DXA-100/200-R single or dual digital accelerometer takes Jewell’s highly accurate analog closed loop sensor technology to the next...

The Model EGAS is a miniature, uniaxial accelerometer featuring ranges from ±5g through ±2500g. This rugged unit weighs less than 1 gram (without leads) and has an over-range limit of 10,000g's. The ½ active bridge is suitable for shunt...

The Model EGAS3 is a miniature, critically damped triaxial accelerometer available in ranges from ±5g through ±2500g. This rugged unit weighs less than 8 grams (without leads) and has an over-range limit of 10,000g's. Operating from nominal 15Vdc...

The Model EGAXT miniature accelerometer combine a damping ratio of 0.7 (nominal) with built-in over-range stops that protect the unit against 10,000g shocks. The model EGAXT features a common piezo-resistive Wheatstone Bridge design with a mV...

The Model EGAXT3 miniature triaxial accelerometer combine a damping ratio of 0.7 (nominal) with built-in over-range stops that protect the unit against 10,000g shocks. This is ideal for applications which may experience rough handling or in...

The Model EGCS accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overrange stops that are set to protect the unit against 10,000g shocks. This is ideal for applications which may experience rough handling or in situations where...

The Model EGCS-D0/D1S accelerometers are critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-D0/D1S accelerometers are critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-D5 accelerometer is critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-S425 is a small, ISO 6487 and SAE J211 compliant piezoresistive accelerometer. This unit features internal temperature compensation, anodized aluminum alloy housing and flexible cable output. This sensing element is damped with fluid...

The Model EGCS3-D triaxial accelerometer is available in ranges from ±5g through ±5000g. With over-range limit to ±10,000g and spring strain relief, this rugged device is ideal for offshore, downhole and shock testing...

The Model EGHS-M is a high amplitude piezoresistive shock accelerometer designed for embedded applications. The accelerometer is available in ±30,000g and ±60,000g ranges, hermetically sealed and packaged in a miniature LCC envelope. The model...

Measurement Specialties has developed this low cost interface amplifier specifically for use with the IB-ACH-01. It is designed to mate directly to the connector supplied with the ACH-01-03 assembly. For use with either the ACH-01-02 or ACH-01-04,...

The Jewell Instruments JMA-165 MEMS accelerometers are a cost effective and viable alternative to traditional force balance designs. This mighty little sensor is CENELEC, AREMA certified, and RoHS...

The Jewell Instruments JMA-165 MEMS accelerometers are a cost effective and viable alternative to traditional force balance designs. This mighty little sensor is CENELEC, AREMA certified, and RoHS compliant. Integrated HEATER...

±5V output version.  The JMA-100/200/300 series is available in single (JMA-100), dual (JMA-200) and triple (JMA-300) axis configurations. This presents a robust and rugged design for industrial use, but with the benefit of low-cost MEMS...

4-20mA output version. The JMA-100/200/300 series is available in single (JMA-100), dual (JMA-200) and triple (JMA-300) axis configurations. This presents a robust and rugged design for industrial use, but with the benefit of low-cost MEMS...

0-5V output version. The JMA-100/200/300 series contains MEMS technology and is available in single (JMA-100), dual (JMA-200) or tri-axis (JMA-300) configurations. Standard measuring ranges span from the precision of ±0.5 g to a broad ±10 g with a...

The LCA-100 accelerometer is a 0.5G to 5G-range sensing pivot and jewel device that meets the demands of many applications. Suspension technology and bandwidths of 60Hz to 250Hz make the LCA-100 popular for a variety of military, commercial and...

The LCF-200 Accelerometer is a ±0.5G to ±5G device designed for applications where high levels of shock and vibration are present. LCF units are characterized by excellent turn on repeatability and very low...

The LCF-2530 is a dual axis version of the rugged, high accuracy LCF Series. The design of the LCF-2530 was optimized to provide the high suspension, servo technology in a small and convenient package for applications requiring a a compact dual axis...

The LCF-3500 Flexure Suspension Fluid Damped Tri-Axial Accelerometer is a ±0.5G to ±5G device designed for applications where high levels of shock and vibration are present. LCF units are characterized by excellent turn on repeatability and very...

The Jewell LSB Series Accelerometer is a general-purpose ±0.5G to ±20G device designed forindustrial, commercial and aerospace sensing...

The Jewell LSBC-R Series Accelerometer is a general purpose ±0.5G to ±20G device designed for rail, commercial, and aerospace sensing...

LSM  Accelerometers have 100,000 hour MTBF reliability and up to 20g full scale sensing range. It offers equivalent features to the LCA in a smaller package — approximately 1" cube. Its wide input range and bandwidth features meet the demanding...

The MiniSense 100 is a low cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Pins are designed for easy installation and are solderable. Horizontal and vertical mounting options are offered. The...

Model MTG-A1 triaxial mounting...

Model MTG-A2 triaxial mounting...

The Emerald Series accelerometer is a low cost, high precision sensor designed with higher accuracy than comparable MEMS devices. Input Ranges From ±0.25G to ±2G°. Applications include robotics, construction equipment, industrial measurement and...

The Model 1207F accelerometer is a small, compact uniaxial device designed for vehicle impact and road testing. Its mechanical overload stops provide high shock protection in rugged applications. Featuring ranges from 50 g to 1000g and frequency...

The Model 121 is a state-of-the-art, 3-Channel DC Differential Amplifier designed to be used with bridge type or differential output accelerometers, pressure transducers, and load cells. The amplifier offers an exceptionally low input noise floor of...

The Model 130 series are remote in-line charge converters designed to be used with piezoelectric accelerometers. The low noise charge converters feature two fixed gain options that convert the high impedance charge output from the accelerometer to a...

...

...

The Model 142 is a remote in-line strain gage amplifier designed to be used with ¼ bridge strain gage instruments. The amplifier features five user selectable gain settings with a gain accuracy of ±0.5% and offers a wide bandwidth to 100kHz. The...

The Model 3022 is a piezoresistive silicon accelerometer packaged in a ceramic substrate with a sealed ceramic cover. The ceramic provides an excellent bonding surface for the customers application specific adhesive. The accelerometer consists of a...

The Model 3028 is a piezoresistive silicon accelerometer packaged on a ceramic substrate with a metal bracket which can be used to bolt the sensor to the mounting location. The accelerometer consists of a micro machined silicon mass suspended by...

The Model 3038 is a hermetically sealed SMD accelerometer designed for high performance applications. The accelerometer incorporates a 2nd generation piezoresistive MEMS sensing element providing outstanding long-term stability. The Model 3038...

The Model 3052A is a silicon MEMS accelerometer with integral temperature compensation. The accelerometer is packaged on a ceramic substrate with an epoxy sealed ceramic cover and is designed for adhesive mounting. The accelerometer is offered in...

The Model 3058A is a silicon MEMS accelerometer with integral temperature compensation. The accelerometer is packaged on a ceramic substrate with a metal bracket which can be used to bolt the sensor to the mounting location. The accelerometer is...

IEPE plug and play accelerometer cable assembly. Standard cable length is 120 inches with 10-32 coaxial connector at each end. Mates with accelerometer models 7100A, 7104A, 7105A, 7108A,...

IEPE plug and play accelerometer cable assembly featuring M3 Coaxial connector and BNC connector. Standard length is 120 inches. Mates with accelerometer model 7101A,...

IEPE plug and play accelerometer cable assembly. Standard cable length is 120 inches. Cable features safety wire holes, #24 AWG tin-plated copper conductors and 3-pin Glenair plug. Mates with accelerometer Model...

IEPE plug and play accelerometer cable assembly featuring 10-32 coaxial connector and BNC connector. Standard cable length is 120 inches. Mates with accelerometer models 7100A, 7104A, 7105A, 7108A,...

IEPE plug and play accelerometer cable assembly for triaxial accelerometers. Featuring 4-pin Microtech connector and three BNC connectors. Standard cable length is 120 inches. Mates with accelerometer models 7131A, 7132A &...

Industrial cable for the 8011 and 8021 condition monitoring accelerometers. The 316A cable includes a 2-pin connector with molded backshell to pigtail leads. It features 2x #22 AWG FEP insulated conductors, braided shield and a flexible TPE jacket....

IEPE plug and play accelerometer cable assembly for triaxial accelerometers. Featuring 4-pin Microtech connector to pigtail leads. Standard cable length is 120 inches. Mates with accelerometer models 7131A, 7132A &...

Industrial cable for the 8011 and 8021 condition monitoring accelerometers. The 318A cable includes a 2-pin connector with molded 90° backshell to pigtail leads. It features 2x #22 AWG FEP insulated conductors, braided shield and a flexible TPE...

Low-noise charge mode plug and play accelerometer cable assembly. Standard cable length is 120 inches with 10-32 coaxial connectors at each end. Mates with accelerometer models 7500A, 7504A, 7505A, 7508A, 7514A &...

Low-noise charge mode plug and play accelerometer cable assembly featuring M3 coaxial connector and 10-32 coaxial connectors. Standard length is 120 inches. Mates with accelerometer model 7501A, 7502A &...

The Model 3255A is a signal conditioned board mountable MEMS accelerometer available in ±25g to ±500g ranges. The package can be mounted in one of two orientations, allowing the measurement axis to be either parallel or perpendicular to the...

Piezoresistive plug and play accelerometer cable assembly featuring #12-48, 5-socket plug. Standard cable length is 120 inches. Mates with accelerometer models 3801A, 4801A, 4810A,...

Piezoresistive plug and play accelerometer cable assembly featuring #12-48, 5-socket plug. Standard cable length is 120 inches. Mates with accelerometer model...

Piezoresistive plug and play accelerometer cable assembly featuring a 5 pin socket plug with straight knurl and strain relief. Standard cable length is 120 inches. Mates with accelerometer...

Instrumentation cable for the model 140 & 142 in-line amplifiers. Featuring shielded model 712 series Binder connector to pigtail leads. Standard cable length is 120...

The Model 53 and 53A Triaxial Crash Test Accelerometers are some of the most popular sensor to be used in crush zone and side impact testing when a triaxial solution is preferred.  The accelerometers feature the next generation of the reliable TE...

The Model 7100A is a high performance IEPE accelerometer with an operating temperature range of -55°C to +150°C. The accelerometer is available in ±50 to ±500g ranges and provides a flat frequency response up to 15kHz. The model 7100A is...

The Model 7101A is a miniature, high performance IEPE accelerometer available in ±50g to ±1000g dynamic ranges.  The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >10kHz utilizing...

The Model 7102A is a miniature adhesive mount IEPE accelerometer available in ±50g to ±2000g dynamic ranges. The accelerometer features a welded hermetic Titanium construction with an M3 connector. The model 7102A accelerometer has an operating...

The Model 7104A is a high performance IEPE accelerometer available in ±50g to ±1000g dynamic ranges. The stud mounted accelerometer features a welded hermetic construction with a side mount 10-32 coaxial connector. The model 7104A incorporates...

The Model 7105A is a high performance IEPE accelerometer available in ±50g to ±1000g dynamic ranges. The stud mounted accelerometer features a welded hermetic construction with a top mount 10-32 coaxial connector. The model 7105A incorporates...

The Model 7108A is a miniature adhesive mount IEPE accelerometer available in ±50g to ±500g dynamic ranges. The accelerometer features a welded hermetic stainless steel construction with a coaxial 10-32 top connector. The model 7108A incorporates...

The Model 7109A is a miniature stud mount IEPE shock accelerometer available in ±5,000g to ±20,000g ranges. The accelerometer features a welded hermetic stainless steel construction with an integral cable for electrical connection. The model 7109A...

The Model 7114A is a high performance IEPE accelerometer available in ±5g to ±50g dynamic ranges. The stud mounted accelerometer features a welded hermetic construction with a side mount connector. The model 7114A incorporates stable piezo-ceramic...

The Model 7120A is a high performance IEPE accelerometer designed for modal applications. The accelerometer is available in ±50g to ±1000g dynamic ranges and offers a flat frequency response to >6kHz. The model 7120A is designed for adhesive...

The Model 7130A is a triaxial IEPE accelerometer available in ±50g to ±500g dynamic ranges. The accelerometer features three independent welded stainless steel assemblies incorporated into a hard anodized aluminum housing. The model 7130A...

The Model 7131A is a miniature triaxial IEPE accelerometer available in ±50g to ±2000g dynamic ranges. The accelerometer features a hermetically sealed Titanium construction with a 4-pin Microtech connector interface. The model 7131A incorporates...

The Model 7132A is a miniature triaxial IEPE accelerometer available in ±10g to ±2000g dynamic ranges and flat frequency response up to >12kHz. The accelerometer features a hermetically sealed titanium construction with a 4-pin Microtech...

The Model 7134A is a true case isolated triaxial IEPE accelerometer available in ±50g to ±500g dynamic ranges. The accelerometer features three internally shielded accelerometer assemblies for superior noise isolation. The assemblies are installed...

The Model 7202A is a case isolated high temperature IEPE accelerometer with internal shielding. The accelerometer has a flat bandwidth up to 15kHz with a resonant frequency greater than 40kHz. The model 7202A is available in ±10 to ±500g ranges...

The Model 7204A is a case isolated high temperature IEPE accelerometer with internal shielding. The accelerometer has a flat bandwidth up to greater than 15kHz with a resonant frequency greater than 40kHz. The model 7204A is available in ±10 to...

The Model 7500A is a piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. The accelerometer incorporates an annular shear mode crystal that provides stable thermal response up to +260°C. The model...

The Model 7501A is a miniature piezoelectric charge mode accelerometer with an operating temperature range to +260°C. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >15kHz with...

The Model 7502A is a miniature piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements. The accelerometer incorporates an annular shear mode crystal that provides stable thermal response up to +260°C....

The Model 7504A is a stud mounted piezoelectric charge mode accelerometer with an operating temperature range to +260°C. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >10kHz and...

The Model 7505A is a stud mounted piezoelectric charge mode accelerometer with an operating temperature range to +260°C. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >10kHz and...

The Model 7508A is a miniature piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements at temperatures up to +200°C.  Featuring a nominal charge output of 5.6pC/g, the model 7508A offers a high signal...

The Model 7514A is a stud mounted piezoelectric charge mode accelerometer with an operating temperature range to +260°C. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >14kHz...

The Model 7530A is a triaxial piezoelectric charge mode accelerometer designed for high frequency vibration and shock measurements.  Model 7530A has a stable thermal response up to +200°C and a nominal charge output of 5.6pC/g which offers optimum...

The Model 7531A is an adhesively mounted triaxial charge mode accelerometer with an operating temperature range to +260°C. The accelerometer is designed for high frequency vibration and shock measurements and offers a wide bandwidth to >10kHz...

The Model 805 is a miniature adhesive mount IEPE accelerometer built on a 3-pin TO-5 header. It is available in ±50g and ±500g dynamic ranges and offers a flat frequency response to 15kHz. The accelerometer features a hermetic construction in a...

The Model 8102 is a low cost, plug & play triaxial accelerometer. Featuring stable piezo-ceramic crystals, the accelerometer incorporates full power and signal conditioning with a maximum current consumption of only 22 micro-amps. The model 8102...

The Model 832 is a low cost, board mountable triaxial accelerometer. Featuring stable piezo-ceramic crystals, the accelerometer incorporates full power and signal conditioning with a maximum current consumption of 4 micro-amps. The model 832 is...

The Model 832M1 is a low cost, board mountable triaxial accelerometer. Featuring stable piezo-ceramic crystals, the accelerometer incorporates full power and signal conditioning with a maximum current consumption of 22 micro-amps. The model 832M1 is...