TE Connectivity

The Model EGCS accelerometers combine a damping ratio of 0.7 (Nominal) with built-in overrange stops that are set to protect the unit against 10,000g shocks. This is ideal for applications which may experience rough handling or in situations where...

The Model EGCS-D0/D1S accelerometers are critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-D0/D1S accelerometers are critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-D5 accelerometer is critically damped with built-in over-range stops that are set to protect the unit against up to 20,000g shocks. This is ideal for applications which may experience rough handling or in situations where the...

The Model EGCS-S425 is a small, ISO 6487 and SAE J211 compliant piezoresistive accelerometer. This unit features internal temperature compensation, anodized aluminum alloy housing and flexible cable output. This sensing element is damped with fluid...

The Model EGCS3-D triaxial accelerometer is available in ranges from ±5g through ±5000g. With over-range limit to ±10,000g and spring strain relief, this rugged device is ideal for offshore, downhole and shock testing...

The Model EGHS-M is a high amplitude piezoresistive shock accelerometer designed for embedded applications. The accelerometer is available in ±30,000g and ±60,000g ranges, hermetically sealed and packaged in a miniature LCC envelope. The model...

Measurement Specialties has applied our decade of experience serving the automotive crash test industry to design the ultimate crash test seat belt restraint sensor. The EL20-S458 provides a super low mass titanium structure to minimize F=MA errors...

EPB is a small pressure probe sensor, small profile, stainless steel, flush mount transducer designed for general media. EPB is offered in pressure ranges from 0-5 to 5000 psi (0-0.35 to 350 bar), vented, sealed, and absolute pressure. EPB's overall...

The EPIH is a subminiature pressure sensor, specifically designed for Dynamic and High Frequency measurements with resonant frequency up to 1.7 MHz. Available with many various housings, EPIH is one of the smallest pressure sensors in the world. The...

The EPL is a surface mount pressure sensor with a stainless steel diaphragm. Available in ranges from 5 to 5000 psi (0.35 to 350 bar), EPL is easy to install on flat surfaces using elastomer or epoxy. Various compensated temperature ranges are...

Ultra Miniature Pressure Transducer, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

Miniature Pressure Transducer, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

Ultra Miniature Pressure Transducer with platinum RTD to sense media temperature, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are...

The FC22 Series low cost compression load cells create new markets previously unrealizable due to cost and performance constraints. This series provides a new level of performance at very low cost. Measurement Specialties' proprietary Microfused™...

The FC23 Series low cost compression force sensors create new markets previously unrealizable due to cost and performance constraints. This series raises the bar in price and performance. Measurement Specialties’ proprietary Microfused™...

The "F" in FDT Series stands for 'Flexible Leads'. These are rectangle elements of piezo film with silver ink screen printed electrodes. Rather than making the lead attachment near the sensor, the piezo polymer tail extends from the active sensor...

Measurement-Specialties’ washer load cell, model FMT, is designed to measure clamping and screwing forces. It is available in standard ranges from 0-4 klbf to 0-64 klbf.The sensor design reduces the hysteresis and sensitivity variations associated...

Measurement-Specialties’ load pins, model FN1010, are designed to fit in the place of the regular mounting unit. The implantation is facilitated by the possibility of modifying a certain number of dimensions. The FN1010 is suitable for numerous...

The FN2114 load cell has been developed for pedal load testing. Its size allows the sensor to be easily installed on the pedals of any vehicle or a fatigue/endurance test bench. Since the forces to be investigated on the brake, clutch or...

The FN2317 is designed with the express purpose of allowing quick and easy installation when measuring forces applied to the handle of the hand brake in automobiles. Through careful placement of metallic strain gauges inside the sensors, accurate...

The FN2420 is a high accuracy compression load cell often used in applications involving calibration presses. It is available in standard ranges from 0-4000 to 0-1000000 lbf and comes with many options, including a concave loading fixture and an...

The FN2570 load cell has been developed for pedal force testing. It attaches easily on all types of pedals and test rigs for endurance and fatigue tests, especially where size is an important factor. Strain is measured with high precision...

The FN2640 is specially designed for overseeing manufacturing processes. It measures with high consistency the regularity of compression load generated when fitting pieces. With its compact design and robust construction, the sensor easily...

The FN3030 measures tension and compression in standard ranges from 0 - 50N to 0 - 100 kN. The FN3030 is well suited for customization in industrial applications and protection levels can be upgraded for use in hostile environments. Additionally,...

The FN3060 S-beam load cell is highly suited for use in test benches and fatigue tests. Due to the mechanical design, the FN3060 is especially durable. It measures tension and compression in standard ranges from 0-50 to 0-500lbf. For high-level...

The FN3148 high precision load cell features accuracy of 0.05% F.S. It is available in standard ranges from 0-10 N to 0-2000 N . Integrated mechanical stops protect against accidental overloads in tension and compression. For high-level output a...

The FN3280 S-beam load cell is designed to measure low loads and comes in standard ranges of 0-0.2 lbf to 0-1 lbf. Integrated mechanical stops protect against accidental overloads up to 100 times F.S. The FN3280 provides a combination of economy and...

Measurement Specialties has applied our decade of experience serving the automotive crash test industry to design the ultimate crash test seat belt restraint sensor. Created for the automobile industry, the FN 4055 measures with excellent accuracy...

The FN4070 load cell measures the effort generated on the anchor point of seat-belts during crash-tests. It has been specifically designed with a replaceable tongue, so that the load cell can be re-used by simply changing the tongue. It also has a...

The FN6163-2 transducer is part of a whole measurement system, which allows verifying the correct pre-straining of the shafts and differentials in a gearbox. Made to the design of the original short secondary shaft, it accurately measures the axial...

The FN7080 is installed in place of the original gear knob on the gear stick of a vehicle and will measure the force required to change gear. Force is measured either in two or three directions. An adapter coupled with an interface collar allows a...

The FN7110 features high accuracy measurement channels in two ranges in the same load cell. The standard ratio between the ranges is 1 to 10, and standard load range combinations go from 0-2 and 0-20 lb through 0-200 and 0-2000 lb. The FN7110's...

The FN7178-2 is designed specifically to be mounted in series with a front wheel shock absorber on a vehicle. It measures the force in three directions to study ride characteristics under a wide range of driving conditions. Mono-directional versions...

The FN7180-3 is designed specifically to measure friction between two elements. Used mainly for automotive application, the sensor controls the efficiency of windshield soaps, elastomeric surfaces, oils and fluids under several conditions. The...

The multiaxial FN7325 measures force from 0-5 kN to 0-250 kN along three axes as well as the corresponding torque from 0-200 N.m to 0-7000 N.m. The FN7325 is simple to use and install and in many diverse applications circumvents the necessity of...

The multi-axial FN7384 is designed for force measurement for tool calibration. Designed for an automotive application, the complete sensor replaces with corresponding dimensions and tolerances, the piece the machine will produce. On strategic places...

The Model FN9620 is a S-Beam load cell with ranges from 500N to 10kN, designed to operate in hostile environments from -40 to 90°C with IP68 ingress protection. It provides high stiffness for high cycle use, low off-axis load sensitivity and high...

The FP110 is designed to measure static and dynamic pressure with the output characteristics substantially kept up to about 20% of the resonant frequency. The all stainless steel construction and flush diaphragm allow the sensor to be used under a...

The FP1124-3 HT Series of pressure transducers is designed specifically to measure pressure on the brake circuit, including ABS brake systems. With its rugged design and excellent thermal characteristics, the FP1124-3 is built to withstand high...

The FS19 load cell, with ranges from 500G to 3000G, uses proven Microfused sensor technology derived from demanding aerospace and automotive applications which employs micro-machined piezoresistive strain gages fused with high temperature glass to a...

The FS20 Series low cost compression force sensor creates new markets previously unrealizable due to cost and performance constraints. This series raises the bar in price and performance. Measurement Specialties’ proprietary Microfused™...

The FX1901 series establishes a breakthrough price/performance value for compression load cells. The FX1901 is a 1% load cell with full scale ranges of 10, 25, 50 or 100 lbf compression. This new, low-cost technology will enable force sensing in a...

The G-Series consist of a single axis conductive tilt sensor on a modern technology in environmentally protected and robust aluminum housing. The fast microcontroller works with a linearization and temperature compensation routines. This fully...

GC-485 DigiSense™ Gage Head is available in five bipolar measurement ranges, with standard strokes from ± .050 inches to ± 1.0 inch. The single ended 8.5 to 30.0 volt dc. input and two-wire, addressable RS-485 output, make the GC-485 ideally...

GCA Series gage head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are...

The GCA-AE Series heavy-duty gage heads enable high performance in environments containing moisture, dirt, and fluid contaminants. These Gage heads are air-extend, spring-retract LVDTs (Linear Variable Differential Transformers) with precision...

GCD Series gage head with stainless steel construction enables the performs in environments containing moisture, dirt and other contaminants. Electronic components are hermetically sealed for added protection against hostile conditions. These are...

The GCD-AE Series heavy-duty DC operated gage heads enable high performance in environments containing moisture, dirt, and fluid contaminants. These Gage heads are air-extend, spring-retract LVDTs (Linear Variable Differential Transformers) with...

The GCD-SE Series is available in five uni-polar measurement ranges, with standard strokes from 0 to 0.1 inch to 0 to 2.0 inches. Operating on a single ended 8.5 to 28.0 volt dc. input, and minimal current draw, the GCD-SE is ideally suited to...

The GCT Series Gage Head Transmitter is available in four different ranges from 0 to .250-inch, to 0 to 2.0-inches. This rugged two wire loop powered gage head is designed for harsh environments with its hermetically sealed stainless steel, housing...

The GY407D is the first rate gyro to support SCPI-like commands, return data in engineering units, and work with an ASCII terminal emulator. It also performs basic functions such as evaluating minimum, maximum, magnitude, and peak-to-peak. The...

The HC485 DigiSense™ Displacement Sensor is available in seven bipolar measurement ranges, with standard strokes from ± .050 inches to ± 3.0 inches. Operating on a single ended 8.5 to 30.0 volt dc. input and a two-wire addressable RS-485 output,...

HCA-RA right angle series LVDTs are tungsten-inert gas (TIG) welded for hermetic sealing with an easy to install radial connector termination. A design improvement to the standard HCA series, the HCA-RA has a through bore design and a right angle...

The HCA Series LVDTs are tungsten-inert gas (TIG) welded to form a hermetic seal that is impervious to dirt, water, steam and corrosive liquids and vapors. They feature a glass-sealed, MS-type connector, but do not permit through bore operation. (A...

The HCD series LVDTs are impervious to dirt, water, steam spray and most corrosives. Tungsten inert gas (TIG) welding provides hermetic sealing that is free from oxidation-producing faults that may cause leakage. They have been qualified at...

The HCT Series LVDT transmitters are the perfect choice for high performance measurements in environments containing moisture, dirt, and fluid contaminants. Operating on a +10.5 to +28VDC loop voltage, the HCT delivers a smooth 4-20mA current loop...

Based on the rugged HS1101LF capacitive humidity sensor, HM1500LF is a dedicated humidity transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with...

Based on the rugged HS1101LF capacitive humidity sensor, HM1520LF is a dedicated humidity transducer designed for measurements at low humidity. Direct measurement of dew point or water concentration can be easily obtained in really cost effective...

The HR Series of LVDTs is highly reliability and is suitable for most general applications. The HR Series features a large core-to-bore clearance, high output voltage over a broad range of excitation frequencies, and a magnetic stainless steel case...

The HR-T Series LVDTs are a variant of the popular HR Series. The HR-T Series LVDTs provide the optimum performance required for a majority of high-temperature applications up to 392°F continuous. The large 1/16 inch bore-to-core radial clearance...

Based on the rugged HTS2010 humidity / temperature sensor, HTM2500 is a dedicated humidity and temperature transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made...

Humidity sensors can improve performance, reduce energy consumption and increase safety in a variety of applications. Increasingly, OEMs are designing relative humidity/temperature sensors into engines, electronics, and other products to improve...

Measurement Specialties has developed this low cost interface amplifier specifically for use with the IB-ACH-01. It is designed to mate directly to the connector supplied with the ACH-01-03 assembly. For use with either the ACH-01-02 or ACH-01-04,...

The IEM 422 is a line powered current transmitter designed for industrial process control applications. The unit consists of a power supply and LVDT conditioner module pre-set to supply a 4 to 20 mA output from a 115 or 230 volt AC supply. The IEM...

The model IT9101 is a rugged and simple device which provides a voltage divider feedback signal for incline position up to 240 degrees. The heart of the IT9101 is a magnetically-damped pendulum coupled to a conductive plastic precision...

The model IT9420 is a rugged yet simple device which provides a 4 to 20 mA current feedback signal for incline position. The heart of the IT9420 is a magnetically-damped pendulum coupled to a conductive plastic precision potentiometer. A highly...

The KMA36 is a magnetic universal encoder for precise rotational or linear measurement. This system-on-chip combines a magneto resistive element along with analog to digital converter and signal processing in a standard small package. By using the...

The KMT32B is a magnetic field sensor based on the anisotropic magneto resistance effect, i.e. it is sensing the magnetic field direction independently on the magnetic field strength for applied field strengths H>25 kA/m. The sensor contains two...

The KMT36H is a magnetic field sensor utilizing the anisotropic magnetoresistance effect. Therefore the sensor is sensing the magnetic field direction rather than the magnetic field strength. The sensor contains three Wheatstone bridges rotated by...

Due to its featured properties - high sensitivity and almost no hysteresis – the KMY sensors are used in a wide range of applications, like magnetic field measurement, revolution counters, proximity detecting, and position measurement. An uniaxial...

Due to its featured properties - high sensitivity and almost no hysteresis – the KMZ sensors are used in a wide range of applications, like magnetic field measurement, revolution counters, proximity detecting, and position measurement. A uniaxial...

Due to its featured properties - high sensitivity and almost no hysteresis – the KMZ10CM sensor is used in a wide range of applications, like magnetic field measurement, revolution counters, proximity detecting, and position...

The MEAS KPSI 27 is a ± 0.25% FSO static accuracy, 1.0" diameter non-submersible pressure transducer specifically designed for demanding industrial applications where the primary criteria are reliability and economy. These units provide repeatable,...

The MEAS KPSI 28 is a ± 0.50% FSO static accuracy, 1.0" diameter non-submersible pressure transducer specifically designed for demanding industrial applications where the primary criteria are reliability and economy. These units provide repeatable,...

The MEAS KPSI 30 is a ± 0.10% FSO static accuracy, 1.0" diameter non-submersible pressure transducer specifically designed for demanding industrial applications where the primary criteria are reliability and economy. These units provide repeatable,...

The MEAS KPSI 300DS, ± 0.50% FSO static accuracy, 0.75" diameter submersible hydrostatic level transducer is specifically designed for small bore applications and to meet the rigorous environments encountered in deep water level measurements. These...

The MEAS KPSI 320 is a ± 0.25% FSO static accuracy, 0.75" diameter submersible hydrostatic level transducer specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The MEAS KPSI 330 is a ± 0.10% FSO static accuracy, 0.75" diameter submersible hydrostatic level transducer specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The MEAS KPSI 335 is a ± 0.05% FSO static accuracy, 0.75" diameter submersible hydrostatic level transducer specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The MEAS KPSI 342 is a ± 0.25% FS TEB accuracy, 0.75" diameter submersible hydrostatic level transducer that combines sensor competencies with the latest in Application Specific Integrated Circuit (ASIC) technology. Implementation of the ASIC...

The 0.75" diameter MEAS KPSI 351 submersible hydrostatic level transducer with ± 0.01 ft H2O accuracy is specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The 0.75" diameter MEAS KPSI 353 submersible hydrostatic level transducer with ± 0.10% FS TEB accuracy is specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The 0.75" diameter MEAS KPSI 355 submersible hydrostatic level transducer with ± 0.05% FS TEB accuracy specifically designed for small bore applications and to meet the rigorous environments encountered in ground water level measurements....

The MEAS KPSI 380 submersible temperature sensor represents the leading edge of temperature sensing technology available today. Incorporating a highly stable media-isolated sensor, the MEAS KPSI™ 380 features a SDI-12 serial-digital interface....

The 1.0" diameter MEAS KPSI 500 submersible hydrostatic level transducer with ± 0.05% FS TEB accuracy represents the leading edge of level sensing technology available today. Incorporating a highly stable media-isolated sensor, the MEAS KPSI 500...

The 1.0" diameter MEAS KPSI 501 submersible hydrostatic level transducer with ± 0.01 ft H2O accuracy represents the leading edge of level sensing technology available today. Incorporating a highly stable media-isolated sensor, the MEAS KPSI 501...

The MEAS KPSI 700 is a ± 1.00% FSO static accuracy, 1.0" diameter submersible hydrostatic level transducer specifically designed to meet the rigorous environments encountered in liquid level measurement and control. It can be configured to perform...

The MEAS KPSI 705 is a ± 0.25% FSO static accuracy submersible hydrostatic level transducer with an elastomeric diaphragm specifically designed to meet the adverse environments encountered in wastewater applications. This suitably-sized transducer...

The MEAS KPSI 710 is a ± 0.50% FSO static accuracy, 1.0" diameter submersible hydrostatic level transducer specifically designed to meet the rigorous environments encountered in liquid level measurement and control. It can be configured to perform...

The MEAS KPSI 720 is a ± 0.25% DSO static accuracy, 1.0" diameter submersible hydrostatic level transducer specifically designed to meet the rigorous environments encountered in liquid level measurement and control. It can be configured to perform...

The MEAS KPSI 730 is a ± 0.10% FSO static accuracy, 1.0" diameter submersible hydrostatic level transducer specifically designed to meet the rigorous environments encountered in liquid level measurement and control. It can be configured to perform...

The MEAS KPSI 735 is a ± 0.05% FSO static accuracy, 1.0" diameter submersible hydrostatic level transducer specifically designed to meet the rigorous environments encountered in liquid level measurement and control. It can be configured to perform...

The MEAS KPSI 750 is a submersible hydrostatic level transducer with a 2.75" elastomeric diaphragm and protective cage specifically designed to meet the adverse environments encountered in wastewater applications. This suitably-sized transducer...

The Linear Ball Bearing (LBB) Series of dimensional gaging probes is engineered for highly precise and repeatable measurements in quality control and metrology applications. LBB within the gaging probe minimize radial play and friction for...

The LCIT series is based on a patented linear position sensor design that features all of the benefits of current LVDT inductive technology, but at a significantly lower cost. The proprietary coil and electronics design of the LCIT has allowed...

Measurement Specialties introduces the new LDM-1000 LVDT conditioning module, for Industrial applications requiring the DIN standard rail mount, form factor. The Measurement Specialties LDM LVDT / RVDT conditioner provides everything you will need...

The 'L' in LDT Series stands for 'laminated' sensor. Typically, a 0.005" (125µm) polyester layer is laminated to a 28 µm or 52µm piezo film element. When used in a 'bending' mode, laminated film elements develop much higher voltage output when...

The LDT1-028K is a multi-purpose, piezoelectric sensor for detecting physical phenomena such as vibration or impact. The piezo film element is laminate to a sheet of polyester (Mylar), and produces a useable electrical signal output when forces are...