Used to charge the battery module LAN-XI Type 2831. Charges in three hours. Input range: 100-240 V AC 50-60Hz.
Used between a LAN-XI module and an AC power source 90-220 V. Matches your country code. Power supply is delivered with each LAN-XI module.
SMB to Microdot adabtor cable to be used with -UA-2107-120- and -UA-2113-066- LAN-XI front panels.
Plug and play access to RPM & Speed signals via the OBD port on the car. Analogue outputs as voltage level (0-5V) or TTL pulse.
Used for stand-alone recorder LAN-XI Notar. Comes with an adaptor for mini-SD that fits into the mini SD-card slot at the rear of the LAN-XI modules. Adaptor for standard SD is included.
Eight-port LAN-switch with PoE and PTPv2 support. 10/100/1000Mbps network switch that can power up to 8 LAN-XI modules. Data transfer and synchronization of LAN-XI modules Powering of up to eight LAN-XI modules, each using a single twisted-pair Ethernet cable Distributed PULSE™ measurement setups Configured specifically for optimum PULSE measurement performance:
Mounting kit consists of all parts required to easily mount the 3660-D frame in a 19-inch rack.
Designed to fill non-used slots in the Type 3660 C or D frame to protect backplane connectors. Empty frame slots can be utilized to store accessories and cables.
Practical hard case for LAN-XI items required for Sonoscout. Also suitable as a case for LAN-XI Notar and portable PULSE systems.
DC power cable to be used between a DC source and the 3660-D and 3660-C Frames. Length 3.0 m.
Used between a car utility socket and aType 3660-C or D frame. Length: 3.0 m.
Standard CAT 6 LAN cable to be used between a module and a PC. Available in 2m, 10m and 30m. Cable is delivered with each LAN-XI module.
Cable for LAN-XI Type 3056, 2x circular 10-pin (M) to 8x BNC (F) 1,0m (3.3ft) max.+70°C (158°F).
DC power cable to be used between a DC power source and 4 LAN-XI modules.
DC power cable to be used between a car utility socket and any LAN-XI module.
Type 3660-A creates a wireless data acquisition front-end by connecting one LAN-XI input module and one LAN-XI Battery Module Type 2831 together. It allows you to stream data wirelessly from any LAN-XI module, giving you the freedom to move your hardware around without cabling. USE SCENARIOS Sonoscout front-end In-vehicle NVH
UA-3102-042 is designed for use with Generator, 4/2-ch. Input/Output Module Type 3160-A-042. USE SCENARIOS Microphones requiring 200 V external polarization General purpose sound and vibration measurements Direct voltage CCLD accelerometers DC responding accelerometers CCLD microphones CCLD tacho probes Connector type: BNC and LEMO Front panel Compatible LAN-XI modules UA-3102-042
UA-3101-080 is the default front panel for LAN-XI CAN Bus Module Type 3058-080, having two independent CAN Bus input connectors. This front panel is ideal for automotive noise, vibration and harshness (NVH) applications. USE SCENARIOS CAN Bus applications, including in-vehicle measurements using Sonoscout Automotive sound quality metrics General sound and
UA-3100-042 is designed for use with Generator, 4/2-ch. Input/Output Module Type 3160-A-042. USE SCENARIOS General purpose sound and vibration measurements Direct voltage CCLD microphones CCLD accelerometers CCLD tacho probes Generator output Connector type: BNC Front panel Compatible LAN-XI modules UA-3100-042 Type 3160-A-042
The Array front panel for LAN-XI UA-2145 is intended for use with hand-held microphone arrays together with a LAN-XI Frame 3660-D. USE SCENARIOS Noise source identification using mapping techniques in conjunction with Acoustic Holography Calculations, Conformal Mapping Calculations and a 3D positioning system Suitable for use with Handheld Arrays: Type
UA‐2121‐030 is the front panel used with LAN‐XI Bridge Module Type 3057‐B‐030. The front‐panel has 3 × 15‐pin sub‐D connectors which allow individual configurations of completion resistors to be made directly on the cable plug. USE SCENARIOS Bridge sensor measurements: 1/1, 1/2, 1/4 bridge strain gauges Strain gauge based sensors